Liquid Epoxies

TC 7000 High temperature epoxy (color red) is a two-part liquid epoxy system for operation temperatures of up to 300°F. Applied at 6 to 10 mils, TC 7000 can be used as a primer for any of the Tapecoat coating products.

When operating temperatures are expected to exceed 180°F, it should be used as a primer for Tapecoat HTMB and 6025 High Temperature Tape Systems.

At a minimum coating thickness of 25 mils, TC 7000 can be considered a stand alone coating.

Add to RFQ

Protal 7200 Cartridge (1000 ml) is a VOC free, 100% solids, 2 part epoxy coating specially formulated to compliment FBE coated pipe.

Price: 
$425.34

Protal 7200 is a VOC free, 100% solids, 2 part epoxy coating specially formulated to compliment FBE coated pipe. It is a high build liquid coating that is brush or spray applied in one coat in the field or shop. It cures very fast to allow quick handling and backfill times.

Price: 
$318.40

Denso Protal 7125 is specifically formulated to be applied to colder substrates at colder ambient temperatures. It is a high build liquid coating that is hand applied in one coat to many areas of in-service pipelines or during pipeline construction in the field or shop. It cures fast to allow quick handling and backfilling, even down to -4°F (-20°C). Protal 7125 is intended for use where a quick cure is required at lower substrate and/or ambient conditions such as during winter applications or on colder operating temperature pipelines. It will also cure after being submersed in water. Used as a rehabilitation coating for existing low temperature in-service operating pipelines, station piping, girth welds, tie-ins, push rack (laybarge applications), abrasion resistant coating for boring applications, repairs to FBE, fittings and fabrication. It may also be used for new construction where colder temperatures exist and preheating or post heating is not practical or feasible.

Price: 
$354.20

Denso Protal 7125 Repair Cartridges are specially formulated for patching and repairing damaged FBE and other liquid coated pipelines. The repair cartridges are packaged in 2-component tubes available in 825 ml and 50 ml and are applied with a dispensing gun (sold separately). Can also be used as a coating for Cadweld areas.

Price: 
$936.50

A fast drying surface tolerant epoxy coating that can be hand or spray applied to wire brushed rusty steel surfaces. Used for above and below ground pipelines, structural steel, bridges, tanks, and other steel surfaces.

Price: 
$330.68

Protal 7200 Repair Cartridges are specially formulated for patching and repairing damaged FBE and other liquid coated pipelines. The repair cartridges are packaged in 2-component tubes that are applied with a dispensing gun (sold separately). Three convenient sizes (400 ml, 50 ml, and 1000ml) are available.

Price: 
$831.00

Powercrete R95 is a single coat, 100% solids, high build epoxy novolac that coats, repairs and rehabilitates pipelines operating at maximum temperatures up to 95ºC (203ºF). As an abrasion resistant overlay (ARO) it is compatible with FBE and CTE mainline coatings and can be used on any metal structure. This 2-component, solvent-free epoxy can easily achieve a dry film thickness of up to 40 mils in a single application and can be hand or spray applied.

Add to RFQ

HBE-95 is a state-of-the-art, 100% solids, two component epoxy coating system which has been specifically formulated as a pipeline coating. Applied to bare steel, HBE products are used for protection of pipeline field joint girth welds, valves and fittings, as a holiday repair material on FBE coated pipe or for pipeline coating rehabilitation.

Please Click Here to View HBE-95 Application

Add to RFQ

Protal ARO is a VOC free, 100% solids liquid epoxy coating formulated to be applied over FBE as an ARO coating (abrasion resistant overlay). It is a 3:1 ratio compatible for most plural component spray units coating that can be spray or hand applied in the field or shop. Protal ARO is used to protect FBE mainline coatings and over Protal 7200 on girth welds during directional drilling, bores, river crossings and other rough terrain applications. Protal ARO can be used to provide additional protection to the coating on bends, fittings and fabrication when severe handling or rough terrain persist.

Add to RFQ

Pages

Subscribe to Liquid Epoxies